Oki Printer 8w Lite User Manual

OKIPAGE 8w Lite  
Setup Guide  
 
English  
Table of contents  
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii  
EEC compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . ii  
Energy Star . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii  
Universal Serial Bus . . . . . . . . . . . . . . . . . . . . . . . . ii  
Table of contents. . . . . . . . . . . . . . . . . . . . . . . . . . . iii  
Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Attaching paper input tray . . . . . . . . . . . . . . . . . 7  
Protective sheet removal . . . . . . . . . . . . . . . . . . 7  
Toner cartridge installation . . . . . . . . . . . . . . . . 8  
Loading paper. . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Printer connection . . . . . . . . . . . . . . . . . . . . . . . 9  
Parallel data connection . . . . . . . . . . . . . . . 10  
USB cable connection . . . . . . . . . . . . . . . . 10  
Power connection. . . . . . . . . . . . . . . . . . . . . . . 10  
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . .1  
Toner cartridge and image drum handling . . . . .2  
Emergency first aid . . . . . . . . . . . . . . . . . . . . . . .3  
Printer driver installation . . . . . . . . . . . . . . . . . . . . 11  
Macintosh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Windows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Parallel connection . . . . . . . . . . . . . . . . . . . 12  
USB connection . . . . . . . . . . . . . . . . . . . . . 12  
Printer features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Printer components . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Setup Guide  
iii  
 
 
iv  
OKIPAGE 8w Lite  
 
English  
Safety instructions  
This printer has been carefully designed to give years of  
safe, reliable performance. As with all electrical equip-  
ment, however, there are a few basic precautions that  
should be taken to avoid personal injury or damaging  
the printer:  
Do not use the printer near water, or spill liquid  
of any kind into it.  
Make sure that the power source matches the rat-  
ing listed on the back of the printer. If you are not  
sure, check with your dealer or with your local  
power company.  
Read this setup guide carefully and save it for  
future reference.  
This printer has an earthed plug as a safety fea-  
ture and will only connect to an earthed outlet. If  
this plug cannot be connected to a power outlet,  
then it is possible that the power outlet is of the  
older, non-earthed type. Contact an electrician to  
have the power outlet replaced. Do not use an  
adapter to defeat the earthing.  
Read and follow all warning and instruction  
labels on the printer itself.  
Disconnect the printer before cleaning. Use only  
a damp cloth. Do not use liquid or aerosol clean-  
ers to clean the printer.  
Place the printer on a firm, solid surface. If the  
printer is placed on something unsteady, it may  
fall and become damaged or injure someone. If  
the printer is placed on a soft surface, such as a  
rug, sofa, or bed, the vents may become blocked  
causing the printer to overheat.  
To avoid damaging the power cable, do not put  
anything on it or place it where it will be walked  
on. If the cable becomes damaged or frayed,  
replace it immediately.  
If an extension cable or power strip is being used  
with the printer, make sure that the total of the  
amperage rating required by all the equipment is  
less than the rating of the extension cable or  
power strip. The total ratings of all equipment  
Do not put the printer on or near a heat source,  
such as a radiator or heat register. Keep it out of  
direct sunlight. Allow enough room around the  
printer for adequate ventilation and easy access.  
Setup Guide  
1
 
   
plugged into the outlet should not exceed 13  
amperes.  
The printer has been dropped, or the cabinet is  
damaged.  
The power outlet into which the printer is con-  
nected must remain accessible at all times.  
The printer does not function normally when fol-  
lowing the operating instructions.  
Opening any cover may expose hot surfaces.  
These are clearly labelled. Do NOT touch them.  
Toner cartridge and image drum  
handling  
Do not insert anything into the ventilation slots  
on the printer; you could get a shock or cause a  
fire.  
Leave unused toner cartridges and image drum  
units in their packages until needed. When  
replacing a toner cartridge or image unit, reuse  
the packaging to dispose of the old toner cartridge  
or image drum unit.  
Aside from the routine maintenance described in  
the user’s guide, do not try to service the printer  
yourself. Opening a cover may expose you to  
shocks or other hazards.  
Do not expose the toner cartridges and image  
drum units to light for more than five minutes.  
Never expose the green drum (inside the image  
drum unit) to direct sunlight.  
Do not make any adjustments other than those  
outlined in the user’s guide as damage may be  
caused to the printer.  
Always hold the image drum unit by the ends —  
never by the middle. Never touch the green drum  
inside the image drum unit.  
If anything happens that indicates that the printer is not  
working properly or has been damaged, disconnect the  
printer from the power source and contact your dealer.  
These are some of the things to look for:  
To avoid damage to the image drum unit, always  
use original toner cartridges.  
The power cable or plug is frayed or damaged.  
Exercise care when removing the toner cartridge.  
Do not let it touch your clothing or porous mate-  
rials. The toner powder causes permanent stains.  
Liquid has been spilled into the printer, or it has  
been exposed to water.  
2
OKIPAGE 8w Lite  
 
 
English  
Small amounts of toner spilled on skin or cloth-  
ing can be readily removed with soap and cold  
water. Using heated water will make removing  
the stain much more difficult.  
Emergency first aid  
IF TONER IS SWALLOWED: Induce vomit-  
ing and seek medical attention. Never attempt to  
induce vomiting or give anything by mouth to a  
person who is unconscious.  
IF TONER IS INHALED: Take the person to an  
open area for fresh air. Seek medical attention.  
IF TONER GETS IN THE EYES: Flush eyes  
with large quantities of cool, NOT cold, water for  
a minimum of 15 minutes keeping eyelids open  
with fingers. Seek medical attention.  
Setup Guide  
3
 
 
Printer features  
8 pages per minute (ppm) output  
Genuine 300 dpi print head  
100 sheet universal paper feeder  
2 Mb of memory as standard with enhanced  
memory management  
Manual feed for envelopes, transparencies, etc.  
Bidirectional Centronics IEEE 1284 parallel  
interface  
USB interface  
Combined ready and power on indicator  
4
OKIPAGE 8w Lite  
 
   
English  
Unpacking  
1
2
3
4
After unpacking the printer and choosing a suitable  
place to put it, check that you have all the necessary  
parts to continue:  
6. Lightproof plastic bag for storing image drum if  
printer must be shipped (not illustrated)  
7. Setup guide (not illustrated)  
1. Paper feed and exit tray  
2. Printer  
8. CD-ROM containing printer drivers and docu-  
mentation (not illustrated)  
3. Image drum cartridge (normally installed inside  
the printer)  
If anything is missing, contact your dealer for a replace-  
ment.  
4. Toner cartridge  
5. Power cable (not illustrated)  
Setup Guide  
5
 
     
Printer components  
1. Paper feed and exit tray  
2. Manual feed slot  
8
3. Ready/power on indicator  
4. Printer cover  
1
7
4
6
5
9. LED array  
10. Image drum  
11. Toner cartridge  
3
2
5. Power switch  
9
6. Power cable socket  
7. Parallel interface connector  
8. USB port  
10  
11  
6
OKIPAGE 8w Lite  
 
   
English  
Setting up  
Before connecting this printer to a computer and power  
supply, the toner cartridge must be installed and paper  
inserted in the paper tray.  
CAUTION:  
Never expose the image drum unit to light for more than 5  
minutes. Never expose the image drum unit to direct sun-  
light. Always hold the image drum unit by the ends. Never  
touch the surface of the green drum inside the image drum  
unit.  
Attaching paper input tray  
1. Insert the paper tray so that the hooks on the  
lower edge latch with the printer.  
2. Remove the image drum (1) from the printer.  
1
2. Push the paper tray forward until it latches and is  
secured on both sides.  
Protective sheet removal  
1. Open the printer cover.  
Setup Guide  
7
 
           
3. Remove the protective sheet (1) from the image  
drum (2).  
1
2
4. Insert the cartridge into the printer, left end (1)  
first as illustrated.  
1
4. Replace the image drum.  
1
Toner cartridge installation  
WARNING  
Be careful when handling the toner cartridge. Do not let  
toner spill on your clothing or other porous materials.  
2
5. Push the coloured tab (2) forward to release the  
toner into the toner hopper.  
1. Remove the tape and shipping insert from the  
image drum.  
6. Close the printer cover.  
2. Shake the toner cartridge to distribute toner  
evenly.  
3. Unwrap the new toner cartridge and carefully  
peel off the sealing tape (1).  
8
OKIPAGE 8w Lite  
 
   
English  
Loading paper  
Printer connection  
Note:  
CAUTION:  
Please refer to the user guide for the types of  
Make sure the printer is disconnected from the power  
supply and the computer is turned off.  
paper to use in this printer.  
1. Set the left paper guide to the marker for the  
required paper size and move the right guide to a  
position slightly wider than your paper width.  
The printer can be connected to a computer using one  
of two methods:  
Parallel port connection for Windows.  
USB port connection for Macintosh and Win-  
dows 98  
Note:  
If the printer is connected using both USB and  
parallel ports, the printer cannot accept simulta-  
neous print jobs. It can only accept, process and  
print one job at a time.  
The following precautions should be observed when  
connecting/disconnecting the interface cable:  
2. Insert the paper so that it is up against and flush  
with the left paper guide.  
Disconnect the interface cable from the computer  
first, then disconnect from the printer.  
3. Adjust the right paper guide to fit snugly but not  
tightly against the edge of the paper.  
Wait a minimum of 5 seconds before reconnect-  
ing the interface cable.  
For envelopes, transparencies, other print media and  
using the manual feed slot, refer to the user’s guide.  
Do not disconnect the interface cable or switch  
the printer off while the printer is printing.  
Setup Guide  
9
 
       
Connect the interface cable to the printer first,  
then connect to the computer.  
2. Connect the Type A (small, flat) connector on the  
other end of the cable to the host computer’s USB  
port.  
Parallel data connection  
See ‘Printer driver installation’ for further information  
on printer installation.  
1. Connect the interface cable to the parallel socket  
(1) on the printer.  
Power connection  
1. Connect the power cable into the power socket  
(3) on the printer, then into a grounded outlet.  
2
2. Switch the printer on using the main power  
switch (4).  
1
3
4
USB cable connection  
The printer comes with a USB interface as standard.  
This requires a Type A to Type B cable, not more than  
5m in length.  
1. Connect the Type B (square) connector on the  
cable to the USB interface connector at the rear of  
the printer (2).  
10  
OKIPAGE 8w Lite  
 
           
English  
Printer driver installation  
A printer driver is software that accepts data from soft-  
ware programs and applications. It then converts this  
data into a format that the printer can understand to pro-  
duce one or more printed pages.  
Macintosh  
1. Switch on the printer then the computer and  
allow the MacOS and Finder to load normally.  
2. Make sure that any virus protection software that  
may be running is temporarily switched off.  
Note:  
Check the Readme file on the disk before carry-  
ing out installation of the printer driver. This file  
may contain information that is required during  
installation of the printer driver.  
3. Insert the disk into the CD-ROM drive on the  
computer then double click on the Installer icon.  
4. Click on the Language button then choose the  
required language.  
The printer can be connected to a computer using one  
of two methods:  
5. Click on the Install button.  
Parallel port connection for Windows.  
6. When the installation is complete, click on the  
USB port connection for Macintosh and  
Windows  
Quit button and restart the computer.  
7. After the computer has restarted, open the  
Note:  
Chooser from the Apple menu.  
If the printer is connected using both USB and  
parallel ports, the printer cannot accept simul-  
taneous print jobs. It can only accept, process  
and print one job at a time.  
8. Click on the OKIPAGE 8w Lite (USB) icon then  
select the printer name that appears in the dia-  
logue box.  
9. Close the Chooser.  
Setup Guide  
11  
 
       
10. From the File menu, select Page Setup. Choose  
the required page size and orientation, then click  
on the OK button.  
3. Click Next and follow on-screen instructions.  
4. Insert the CD into the CD-ROM drive. Click  
Next, then select the CD-ROM drive to search for  
a USB driver.  
Windows  
5. Click on Next again to install the USB driver fol-  
lowing the on-screen instructions.  
Parallel connection  
6. After installing the USB driver, Windows will  
report that it has detected a new Okipage printer.  
1. Insert the OKIPAGE 8w Lite Manuals and Soft-  
ware CD that came with the printer into the CD-  
ROM drive.  
Note:  
Allowing Windows to automatically intsall the  
driver for an Okipage printer does NOT fully in-  
stall the necessary software. Installation of the  
printer driver must be done using the setup rou-  
tine from the CD that came with the Okipage  
printer.  
2. Click on Start - Run.  
3. Type D:\setup.exe (where “D” represents your  
CD-ROM drive letter). Click OK.  
4. Follow the on-screen instructions  
USB connection  
7. Click on Cancel to close the window, then click  
on Start - Run.  
Note:  
The USB port capability can only be used with  
Windows 98.  
8. Type D:\setup.exe (where D represents the CD-  
ROM drive letter). Click OK.  
1. Connect the printer and USB cable (see “USB  
connection”) to your computer and switch on the  
printer.  
9. Select Install Printer Driver. Follow the on-screen  
instructions, selecting USB port connection for  
the printer.  
2. Windows will report that it has detected unknown  
hardware.  
12  
OKIPAGE 8w Lite  
 
         
English  
Index  
Printer driver installation. . . . . . . . . . . . . . . . . . . . . . . 11  
C
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Windows parallel connection . . . . . . . . . . . . . . . . 12  
Windows USB connection . . . . . . . . . . . . . . . . . . 12  
Protective sheet removal . . . . . . . . . . . . . . . . . . . . . . . . 7  
Component identification . . . . . . . . . . . . . . . . . . . . . 5, 6  
Connection  
Parallel interface . . . . . . . . . . . . . . . . . . . . . . . . . .10  
Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
S
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Setting up  
F
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Loading paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Paper input tray . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Parallel interface connection . . . . . . . . . . . . . . . . 10  
Power cable connection . . . . . . . . . . . . . . . . . . . . 10  
Protective sheet removal . . . . . . . . . . . . . . . . . . . . 7  
Toner cartridge installation . . . . . . . . . . . . . . . . . . 8  
USB interface connection. . . . . . . . . . . . . . . . . . . 10  
P
Paper  
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Paper types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Paper input tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Parallel interface connection . . . . . . . . . . . . . . . . . . . .10  
Power cable connection . . . . . . . . . . . . . . . . . . . . . . . .10  
Printer  
T
Toner cartridge installation . . . . . . . . . . . . . . . . . . . . . . 8  
Component identification . . . . . . . . . . . . . . . . . 5, 6  
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Setting up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
U
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
USB interface connection . . . . . . . . . . . . . . . . . . . . . . 10  
Setup Guide  
13  
 
 
OKI SYSTEMS COMPANIES  
Oki Systems (UK) Limited  
550 Dundee Road  
Slough Trading Estate  
Slough  
Berks SL1 4LE  
Tel: +44 (0) 1753 819 819  
Fax: +44 (0) 1753 819 899  
Oki Systems (Ireland) Limited  
The Square Industrial Complex  
Tallaght  
Dublin 24  
Tel: +353 (01) 459 8666  
Fax: +353 (01) 459 8840  
Hawthorn Business Centre  
Adelaide Industrial Estate  
Falcon Road  
Belfast BT12 6HP  
Tel: +44 (01232) 572 355  
Fax: +44 (01232) 572 350  
14  
OKIPAGE 8w Lite  
 

Milan Technology Network Card CCSF30XX 100 User Manual
Multi Tech Systems Network Card MTS2EA User Manual
Network Computing Devices Network Router PS6U1UHE User Manual
Nike Watch SR626SW User Manual
Nintendo Video Game Console 148Hx210W User Manual
NordicTrack Home Gym 831298651 User Manual
Northern Industrial Tools Portable Generator 10000 BDG User Manual
Olympus Computer Drive MAUSB 200 User Manual
Omnimount TV Mount LEDW60 User Manual
Palm Cell Phone Electronics Handheld Devices User Manual