Nokia Bluetooth Headset HDW 2 User Manual

Electronic user's guide released subject to "Nokia User's Guides Terms and Conditions,

7th June, 1998"

User’s Guide for the Wireless

Headset (HDW-2)

9355260

Issue 1

Contents

1. Introduction.......................................................................................................5

Bluetooth wireless technology ................................................................................................................ 5

Chargers and batteries............................................................................................................................... 6

The card in the sales package.................................................................................................................. 6

2. Getting started ..................................................................................................7

Overview......................................................................................................................................................... 7

Charging the battery .................................................................................................................................. 8

When the battery charge falls low ..................................................................................................... 9

Changing the battery ................................................................................................................................. 9

Switching the headset on or off ...........................................................................................................11

Taking the headset into use for the first time ..................................................................................11

Adjusting the headset to your ear........................................................................................................12

Placing the headset on the ear..............................................................................................................14

Troubleshooting .........................................................................................................................................14

3. Using the headset............................................................................................15

Connecting the paired headset to your phone .................................................................................15

Making a call ..............................................................................................................................................16

Voice dialling ..............................................................................................................................................16

Redialling the last dialled number........................................................................................................16

Answering a call ........................................................................................................................................16

Ending a call ...............................................................................................................................................17

Rejecting a call...........................................................................................................................................17

Automatic answer.....................................................................................................................................17

Adjusting the earphone volume............................................................................................................17

Switching the call between phone and headset ..............................................................................17

Disconnecting the headset from the phone ......................................................................................18

Reconnecting the paired headset to your phone..........................................................................18

Using the headset with several phones ..............................................................................................19

Using the headset with several paired phones..............................................................................19

Resetting the headset ..............................................................................................................................20

4. Battery information.........................................................................................21

Care and maintenance ........................................................................................23

1. Introduction

The Wireless Headset HDW-2 can be connected without wires to a compatible

phone that supports Bluetooth wireless technology. This gives you complete

freedom for making and receiving calls while on the move or at the office.

Read this user’s guide carefully before using the headset. More detailed

information is provided by your phone's own user's guide. Do not use this Wireless

Headset (HDW-2) user’s guide in place of your phone’s user's guide, which

provides important safety and maintenance information.

■ Bluetooth wireless technology

Since Bluetooth devices communicate using radio waves, your Bluetooth phone

and headset do not need to be in a line of sight. The two devices only need to be

within a maximum of 10 meters of each other, although the connection can be

subject to interference from obstructions, such as walls, or from other electronic

devices.

The headset is specially designed for Nokia phones that support Bluetooth

wireless technology. The headset can, however, be used with any compatible

Bluetooth devices that support the Handsfree or Headset profile. (Here, "Profile"

means a set of Bluetooth commands that your phone uses for controlling the

headset.)

The headset provides the best performance when it is used with a compatible

Nokia phone. If you use the headset with a phone produced by another

manufacturer, all the functions described in this user’s guide may not be available.

In some countries, there may be restrictions on using Bluetooth devices. Check

with your local authorities.

■ Chargers and batteries

Check the model number of any charger before using it with this device. The Wireless

Headset HDW-2 is intended for use with the following chargers: ACP-8, ACP-9 and ACP-12.

Warning! Use only batteries and chargers approved by Nokia for use with this

particular accessory. The use of any other types will invalidate any approval or

warranty applying to the accessory, and may be dangerous.

For availability of approved batteries and chargers, please check with your local

dealer.

When you disconnect the power cord of any accessory, grasp and pull the plug, not

the cord.

■ The card in the sales package

The card contains the Bluetooth passkey you need for pairing your phone with the

headset. Keep this card in a secure place.

For instructions on using the passkey, see Taking the headset into use for the first

time on page 11.

2. Getting started

■ Overview

The headset contains the following parts:

1 - Power key: Switches the

headset on and off.

2 - Answer/end key: Answers or

ends the call. This key can also be

used for voice dialling, redialling

and switching an active call

between the headset and the

phone.

3 - Indicator light: Displays the

current status of the headset.

4 - Volume up: Increases the

earphone volume during a call.

5 - Volume down: Decreases the earphone volume during a call.

6 - Earphone: Relays the caller’s voice.

7 - Microphone: Picks up your voice.

8 - Charger connector

9 - Battery door

10 - Earloop

■ Charging the battery

The headset has a rechargeable NiMH battery. If you need to replace the battery,

you can purchase a new one from your nearest authorised dealer.

To charge the battery:

1. Connect the charger cable to the headset. For a list of compatible chargers,

see Chargers and batteries on page 6.

2. Connect the charger to an AC wall outlet. The red indicator light is displayed

during charging. Charging the battery fully takes between 1 and 2 hours,

depending on the charger.

3. When the battery is fully charged, the green indicator light is shown.

Disconnect the charger from the AC wall outlet and the headset.

When the battery charge falls low

The fully charged battery has power for up to 3 hours of talk time and up to 60

hours of standby time. (In standby mode, the headset is switched on but no call is

in progress.)

When the battery is running out of power, the headset beeps. Charge the battery

as described above.

■ Changing the battery

When the operating time is noticeably shorter than normal, it is time to buy a new

battery.

To change the battery:

1. Open the battery door by gently sliding it

backwards (1).

2. Remove the battery by pulling the strap (2).

3. Detach the battery from the

connector (3).

4. Attach the new battery to the

connector.

5. Place the connector in the space

reserved for it and set the battery into its

place (4).

6. Close the battery door and make sure it is

properly locked in place (5).

■ Switching the headset on or off

To switch on: Press and hold the power key for 2 seconds. The headset beeps and

the green indicator light starts blinking. The blinking continues until the headset

is connected to your phone, within 5 minutes. If the headset cannot be connected

to your phone during this time, the headset is switched off.

To switch off: Press and hold the power key for 2 seconds. The headset beeps and

the red indicator light is displayed briefly.

■ Taking the headset into use for the first time

1. Make sure that your phone is switched on.

2. Switch on the headset.

3. Enter your phone’s Bluetooth menu and make sure that the Bluetooth feature

is activated.

4. Enter the submenu where you can set the phone to search for Bluetooth

devices, and start the search.

The phone searches for all Bluetooth devices within about 10 meters and

displays them as a list.

5. Select the headset from the list.

6. Enter the passkey to associate ("pair") and connect the headset to your phone.

The passkey is marked on the card that is provided in the sales package of the

headset.

Once you have entered the passkey, your phone becomes the default phone for

the headset, if the headset has not been previously paired with another phone.

See also Using the headset with several phones on page 19.

The headset beeps and appears in the phone menu where you can view the

Bluetooth devices that are currently paired with your phone.

7. Start using the headset (see page 15).

■ Adjusting the headset to your ear

The headset can be worn on either ear.

For optimal fit, choose between the two different-sized earloops provided in the

sales package.

To change the orientation of

the earpiece, detach the

earloop from the body part as

shown in the figure below,

and place it back according to

the L/R markings on the

earloop. L stands for the left

ear, and R stands for the right

ear. When, for example, the R

marking is visible, you can

wear the headset on your

right ear.

■ Placing the headset on the ear

Slide the earloop gently

behind your ear as shown in

the figure below:

■ Troubleshooting

If you cannot connect the headset to your phone, proceed as follows:

• Make sure that the headset is switched on and paired with your phone.

• Make sure that the Bluetooth feature is activated on your phone.

• Check that the headset is within a maximum of 10 meters of your phone and

that there are no obstructions, such as walls, or other electronic devices

between the headset and the phone.

• The pairing information list of the headset may be full. The headset can store

the information of up to 8 phones at a time. If the list becomes full, reset the

headset to the original settings (see page 20).

• If the headset does not respond to your actions, remove the battery for a short

while.

3. Using the headset

Before using the headset, make sure that:

• The headset is paired and connected to your phone. For instructions on pairing

the headset, see Taking the headset into use for the first time on page 11. For

instructions on connecting the headset, see Connecting the paired headset to

your phone below.

• The phone’s Bluetooth feature is on; see your phone’s user’s guide

• The headset is switched on; see Switching the headset on or off on page 11

• The headset is within a maximum of 10 meters of your phone

• There are no obstructions, such as walls, or other electronic devices between

the headset and the phone.

For information on using the headset with several phones, see page 19.

■ Connecting the paired headset to your phone

The headset is disconnected from the phone when, for example, the headset is

switched off.

To connect the headset to your phone, switch on the headset or make the

connection in the phone’s Bluetooth menu.

Note that switching on the headset creates the connection automatically only if

you have set the phone to accept Bluetooth connection requests without your

permission. In Nokia phones this can be done by changing your paired devices

settings in the Bluetooth menu.

For more information on disconnecting the headset from your phone, see page 18.

■ Making a call

When the headset is connected to your phone, make the call by using your phone

in the normal way.

■ Voice dialling

When no call is in progress, press and hold the answer/end key until you hear a

tone that indicates that you can say the desired name ("voice tag"). Say the voice

tag. The phone plays the voice tag and dials the related phone number.

You can also activate voice dialling with your phone. For details on voice dialling,

see your phone’s user’s guide. Note that this functionality is only available if your

phone supports voice dialling.

■ Redialling the last dialled number

Press the answer/end key twice briefly while no call is in progress.

■ Answering a call

Press the answer/end key to answer the call.

You can also answer the call by using your phone in the normal way.

When you receive a call, you hear a ringing tone selected on your phone also

through the headset.

■ Ending a call

Press the answer/end key to end the currently active call.

You can also end the call by using your phone in the normal way.

■ Rejecting a call

If you do not want to answer a call, briefly press the answer/end key twice.

■ Automatic answer

If the Automatic answer function is set on in your phone, the phone automatically

answers the incoming call after one ring.

■ Adjusting the earphone volume

Press the volume up key to increase or the volume down key to decrease the

volume. To adjust the volume quickly, press and hold either of these keys.

■ Switching the call between phone and headset

You can switch the active call between the headset and the phone. This

functionality is supported in all compatible Nokia phones.

To switch the call from headset to phone:

• Press and hold the answer/end key. OR:

• Use the respective function in your phone.

To switch the call from phone to headset:

• Press and hold the answer/end key. OR:

• Use the respective function in your phone.

■ Disconnecting the headset from the phone

You can disconnect the headset from your phone when, for example, you want to

use another Bluetooth device with your phone.

The headset can be disconnected in the following ways:

• Switch off the headset. OR:

• Disconnect the headset in the phone’s Bluetooth menu. OR:

• Move the headset more than 10 meters away from the phone.

The headset is also disconnected if its battery becomes flat.

Note that you do not need to delete the pairing with the headset to disconnect it.

When you reconnect a paired headset, you will not be asked for its passkey.

Reconnecting the paired headset to your phone

See Connecting the paired headset to your phone on page 15.

■ Using the headset with several phones

Before the headset can be used with your phone, the phone has to be paired with

the headset. The headset can be paired with up to 8 phones but connected to only

one phone at a time.

Using the headset with several paired phones

The phone that was first paired with the headset is called the "default phone". The

phone that was last used with the headset is called the "last used phone".

If the headset is switched on within 10 metres of several paired phones, the

headset will try to connect to the "default phone" within a few seconds.

If the headset cannot connect to the "default phone" (because, for example, it is

switched off or its user rejects the connection), the headset tries to connect to the

"last used phone" within a few seconds.

If the headset cannot connect to either of the phones, it remains discoverable for

other phones for the next 5 minutes, which is displayed by the blinking green

indicator light. If you do not make the connection during this time, the headset is

switched off automatically.

If you want to use the headset with a paired phone that is not a "default phone" or

"last used phone", make the connection in your phone’s Bluetooth menu.

■ Resetting the headset

You can reset the headset to the original settings to, for example, change the

default user of the headset.

When you reset the headset, all of its settings, including pairing information, are

cleared.

To reset the headset: Press and hold the power key together with the volume up

key for 10 seconds. After the headset has been reset, the headset beeps twice and

the red and green indicator lights alternate for several seconds.

4. Battery information

Your headset is powered by a rechargeable battery. Take good care of the battery

and follow the guidelines below.

Charging and discharging

•

Note that a new battery's full performance is achieved only after two or three complete

charge and discharge cycles!

•

The battery can be charged and discharged hundreds of times but it will eventually wear

out. When the operating time is noticeably shorter than normal, it is time to buy a new

battery.

•

Use only batteries approved by Nokia and recharge your battery only with the chargers

approved by Nokia. Unplug the charger when not in use. Do not leave the battery

connected to a charger for longer than a week, since overcharging may shorten its lifetime.

If left unused a fully charged battery will discharge itself over time.

•

Temperature extremes can affect the ability of your battery to charge.

For good operation times with NiMh batteries, discharge the battery from time to time by

leaving your headset switched on until it turns itself off. Do not attempt to discharge the

battery by any other means.

•

Use the battery only for its intended purpose.

Never use any charger or battery which is damaged.

Leaving the headset in hot or cold places, such as in a closed car in summer or winter

conditions, will reduce the capacity and lifetime of the battery. Always try to keep the

battery between 15°C and 25°C (59°F and 77°F). A headset with a hot or cold battery may

temporarily not work, even when the battery is fully charged.

Batteries' performance is particularly limited in temperatures well below freezing.

Do not dispose of a battery in a fire!

•

Dispose of batteries according to local regulations (e.g. recycling). Do not dispose

as household waste.

Care and maintenance

Your headset is a product of superior design and craftsmanship and should be treated with

care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this

product for many years.

•

Keep all accessories out of the reach of small children.

Keep the headset dry. Precipitation, humidity and all types of liquids or moisture can

contain minerals that will corrode electronic circuits.

•

Do not use or store the headset in dusty, dirty areas. Its moving parts can be damaged.

Do not store the headset in hot areas. High temperatures can shorten the life of

electronic devices, damage batteries, and warp or melt certain plastics.

•

Do not store the headset in cold areas. When it warms up (to its normal temperature),

moisture can form inside, which may damage electronic circuit boards.

•

Do not attempt to open the headset. Non-expert handling may damage it.

Do not drop, knock or shake the headset. Rough handling can break internal circuit

boards.

•

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the headset.

Do not paint the headset. Paint can clog the moving parts and prevent proper operation.

If the headset is not working properly, take it to your nearest qualified service facility. The

personnel there will assist you and, if necessary, arrange for service.

Miele Double Oven H 5051 B User Manual
Milwaukee Cordless Saw 2682 20 User Manual
NEC Recording Equipment 760417 User Manual
NEC Speaker System PX 60SP3U User Manual
New Buck Corporation Fan Heater Model 80 User Manual
Nikon Film Camera 1683 User Manual
Nikon Scanner AX 210 User Manual
NordicTrack Treadmill CMX500 User Manual
Omega Speaker Systems Computer Monitor iLD Series User Manual
Parker Hannifin DVD VCR Combo Karrykrimp 2 User Manual